Calibration of DEM parameters for coated sunflower seeds based on dynamic stacking angle
Abstract
To address the errors associated with the application of existing Discrete Element Method simulation parameters in roller-type precision seeders, this study focused on calibrating the key contact parameters of the ‘Xinhe No. 1’ coated confectionary sunflower seeds, so as to provide a reliable simulation foundation for the optimization of the seeders. Through dynamic stacking angle experiments and comparative trials involving confectionary sunflowers (including Xinhe No. 1) and oil sunflowers with significantly different physical properties, the optimal working conditions for the rotating drum were determined as a rotation speed of 10 r/min, 304 Stainless Steel as the inner wall material, and a filling ratio of 30%. The study also clarified the variation patterns of the dynamic stacking angle. Physical experiments were conducted to measure the static friction coefficients, restitution coefficients, and inter-seed restitution coefficients between Xinhe No. 1 seeds and three materials: 304 Stainless Steel, Q235 Steel, and ABS Plastic. The physical dynamic stacking angle was obtained via a rotating drum experiment. A single-factor experiment was used to determine the range of simulation parameters, and a second-order orthogonal experiment was conducted using Design-Expert software to optimize contact parameters with the physical dynamic stacking angle as the target. The parameters were subsequently validated using the Discrete Element Method (DEM) simulation software EDEM 2022.3, hereinafter abbreviated as EDEM simulations. Finally, rolling friction coefficients between seeds and Q235 Steel and ABS Plastic were obtained through both simulation and physical experiments using alternative contact materials. The results showed that the static friction coefficients between Xinhe No. 1 and 304 Stainless Steel, Q235 Steel, and ABS Plastic were 0.32, 0.36, and 0.25, respectively; the restitution coefficients were 0.42, 0.39, and 0.32; and the rolling friction coefficients were 0.012, 0.011, and 0.010. The measured values of the inter-seed static friction coefficient, restitution coefficient, and rolling friction coefficient were 0.31, 0.43, and 0.010, respectively. The relative error between simulated and physical stacking angles was <1.5%. Calibrated DEM parameters for Xinhe No. 1 coated sunflower seeds provide a theoretical basis for optimizing the design of sunflower precision seeders.
Keywords: sunflower seed, DEM, parameter calibration, dynamic stacking angle, hill-drop planter
DOI: 10.25165/j.ijabe.20261901.10103
Citation: Liu C J, Zhao W Y, Feng B, Shi L R, Sun B G, Dai F, et al. Calibration of DEM parameters for coated sunflower seeds based on dynamic stacking angle. Int J Agric & Biol Eng, 2026; 19(1): 283–294.
References
[1] Li C F, Liu J F, Feng X J, Li J P. Modern machine design technique and agricultural machinery design. Journal of Agricultural Mechanization Research, 2006（5）: 186–188. （in Chinese）
[2] Wang L, He X W, Hu C, Guo W S, Wang X F, Xing J F, et al. Measurement of the physical parameters and calibration of discrete element simulation parameter of coated cotton seed. Journal of China Agricultural University, 2022; 27（6）: 71–82. （in Chinese）
[3] Chen L, Yu N H, Wang L Z, Fan J J, Lei G, Liu X P, et al. Measurement of contact parameters and discrete element simulation calibration of rice bran and broken rice. Journal of Agricultural Science and Technology, 2024; 26（2）: 127–136. （in Chinese）
[4] Shi L J, Yang M L. Ananlysis on research hotspots in agricultural engineering in China based on scientometrics. Transactions of the Chinese Society of Agricultural Engineering, 2016; 32（Z2）: 430–438. （in Chinese）
[5] Zeng Z W, Ma X, Cao X L, Li Z H, Wang X C. Critical review of applications of discrete element method in agricultural engineering. Transactions of the Chinese Society for Agricultural Machinery, 2021; 52（4）: 1–20. （in Chinese）
[6] Ma Z, Li Y M, Xu L Z. Summarize of particle movements research in agricultural engineering realm. Transactions of the Chinese Society for Agricultural Machinery, 2013; 44（2）: 22–29. （in Chinese）
[7] Yuan J B, Wang J F, Li H, Qi X D, Wang Y J, Li C. Optimization of the cylindrical sieves for separating threshed rice mixture using EDEM. Int J Agric & Biol Eng, 2022; 15（2）: 236–247.
[8] Zhang Z G, Zeng C, Xing Z Y, Xu P, Guo Q F, Shi R M, et al. Discrete element modeling and parameter calibrationof safflower biomechanical properties. Int J Agric & Biol Eng, 2024; 17（2）: 37–46.
[9] Xie K T, Zhang Z G, Wang F A, Yu X L, Wang C L, Jiang S F. Calibration and experimental verification of discreteelement parameters of Panax notoginseng root. Int J Agric & Biol Eng, 2024; 17（4）: 13–23.
[10] Zheng G, Qi B, Zhang W Y, Song S M, Wu Y, Xia Q Q, et al. Calibration and testing of discrete element simulation parameters for spinach seeds. Computational Particle Mechanics, 2025; 12: 479–490.
[11] Wan Y, Zhang B W, Lai Q H, Gong Y, Qingxu Y, Chen X. Determination of melon seed physical parameters and calibration of discrete element simulation parameters. Plos One, 2024; 19: e0300516.
[12] Yu Q X, Liu Y, Chen X B, Sun K, Lai Q H. Calibration and experiment of simulation parameters for Panax notoginseng seeds based on DEM. Transactions of the Chinese Society for Agricultural Machinery, 2020; 51（2）: 123–132. （in Chinese）
[13] Li Y C, Tian X L, Zhao Y, Liu X H, Zhou M L, Dai F S, et al. Parameter calibration and experiment of polyhedral cottonseed discrete element based on tavares model. Transactions of the Chinese Society for Agricultural Machinery, 2024; 55（7）: 124–131, 220. （in Chinese）
[14] Xia J F, Zhang P, Yuan H W, Du J, Zheng K, Li Y F. Calibration and verification of flexible rice straw model by discrete element method. Transactions of the Chinese Society for Agricultural Machinery, 2024; 55（9）: 174–184. （in Chinese）
[15] Liu R, Li Y J, Liu Z J, Liu L J, Lyu H T. Analysis and calibration of discrete element parameters of coated maize seed. Transactions of the Chinese Society for Agricultural Machinery, 2021; 52（S1）: 1–8, 18. （in Chinese）
[16] Ao R G L, Zhang W J, Wang S, Liu W H, Yu Z H. Measurement of physical contact parameters and discrete element simulation calibration of sunflower seeds. Journal of Agricultural Mechanization Research, 2023; 45（4）: 139–147. （in Chinese）
[17] Feng J X, Lin J, Li S Z, Zhou J Z, Zhou Z X. Calibration of discrete element parameters of particle in rotary solid state fermenters. Transactions of the Chinese Society for Agricultural Machinery, 2015; 46（3）: 208–213. （in Chinese）
[18] Santos K G, Campos A V P, Oliveira O S, Ferreira L V, Francisquetti M C, Barrozo M A S. DEM simulations of dynamic angle of repose of acerola residue: A parametric study using a response surface technique. Blucher Chemical Engineering Proceedings, 2015; 1（2）: 1–8.
[19] Cai W Y, Wang L Q, Xu L M. Discrete elemental parameter calibration of ultrafine calcium carbonate based on static and dynamic angle of repose. China Powder Science and Technology, 2024; 30（4）: 81–93. （in Chinese）
[20] Wu Z, Wang L Q, Xu L M, Gao W J. Discrete element parameters calibration of titanium dioxide based on static and dynamic repose angles. China Powder Science and Technology, 2023（4）: 108–119. （in Chinese）
[21] Yan J W, Wei S, Zhang W P, Zhang F G. Calibration of discrete element contact parameters for white radish seed particles. Journal of Chinese Agricultural Mechanization, 2023; 44（8）: 1–11. （in Chinese）
[22] Shi L R, Ma Z T, Zhao W Y, Yang X P, Sun B G, Zhang J P. Calibration of simulation parameters of flaxed seeds using discrete element method and verification of the seed-metering experiment. Transactions of the Chinese Society of Agricultural Engineering, 2019; 35（20）: 25–33. （in Chinese）
[23] Zhang W J, Yang M, Zhang Q L, Wang Q Z, Li X J, Bi Y, et al. Discrete element simulation parameter calibration and experimental verification of sea buckthorn material. Journal of Northeast Agricultural University, 2023; 54（10）: 59–69. （in Chinese）
[24] Ma Y C, Wang Z, Shi L R, Zhao W Y, Sun B G, Dai F, et al. Determination the intrinsic parameters and calibration of contact parameters for wheat seed particles. Journal of China Agricultural University, 2025; 30（3）: 175–184. （in Chinese）
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 International Journal of Agricultural and Biological Engineering
This work is licensed under a Creative Commons Attribution 4.0 International License.
IJABE is an international peer reviewed, open access journal, adopting Creative Commons Copyright Notices as follows.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
