Design and experiment of a six-row air-blowing centralized precision seed-metering device for Panax notoginseng

Qinghui Lai, Kai Sun, Qingxu Yu, Wei Qin

Abstract


Panax notoginseng is grown mainly in Yunnan Province. Under the present high-density planting patterns for the plant, to solve the problems of a high rate of seed damage and the inability to use a traditional single air-blowing metering device, this paper designs a six-row air-blowing centralized precision seed-metering device for P. notoginseng to realize mechanized precision seeding of this species. This paper describes the working principle of the seed-metering device, and the main structural parameters are determined by combining theoretical calculations with simulation analysis. A mechanics model of the seed filling, cleaning and pressing processes of the seed-metering device was constructed. The seeds of P. notoginseng in Yunnan Province were selected as experimental subjects. An experimental study on the seed-metering performance of the seed-metering device was carried out using the quadratic rotation orthogonal combination test method. The outlet pressure of the air nozzle, forward velocity and cone angle of the hole were selected as test factors. Mathematical models of the grain spacing qualified index, miss index, multiple index and the coefficient of variation of the row displacement consistency were established to analyze the order of factors affecting indicators. Through parameter optimization, the optimum combination of parameters was determined as follows: the cone angle of the hole is 50°, the forward velocity is less than 0.73 m/s, and the outlet pressure of the air nozzle is 0.32-0.52 kPa. The qualified index of grain spacing is higher than 94%, the miss index is less than 3%, the multiple index is less than 5%, and the coefficient of variation of the row displacement consistency is less than 5%. The test results are essentially consistent with the optimization results. The metering device meets the requirements of precision seeding of P. notoginseng. This study provides a basis for the design of a six-row air-blowing centralized precision seed-metering device for P. notoginseng.
Keywords: Panax notoginseng, air blowing, seed-metering device, optimization design, air distribution mechanism
DOI: 10.25165/j.ijabe.20201302.5161

Citation: Lai Q H, Sun K, Yu Q X, Qin W. Design and experiment of a six-row air-blowing centralized precision seed-metering device for Panax notoginseng. Int J Agric & Biol Eng, 2020; 13(2): 111–122.

Keywords


Panax notoginseng, air blowing, seed-metering device, optimization design, air distribution mechanism

Full Text:

PDF

References


Mao X, Yi S J, Tao G X, Y ang L, Liu H Y, Ma Y C. Experimental study on seed-filling performance of maize bowl-tray precision seeder. Int J Agric & Biol Eng, 2015; 8(2): 31–38.

Yin H Y. Research on the development of domestic and foreign pneumatic seed sowing device. Agricultural Science & Technology and Equipment, 2013; 230(8): 25–26. (in Chinese)

Zhang Z P, Ma C L, Zuo C C. The Development of the seed-metering device for precision planter and its theoretical study. Journal of Jilin University of Technology, 1995; 4: 112–117. (in Chinese)

ArzuYazgi, Adnan Daegirmencioglu. Optimisation of the seed spacing uniformity performance of a vacuum-type precision seeder using response surface methodology. Biosystems Engineering, 2007; 97(3): 347–356.

Yazgi A, Daegirmencioglu A. Measurement of seed spacing uniformity performance of a precision metering unit as function of the number of holes on vacuum plate. Measurement, 2014; 56(10): 128–135.

Zulin Z, Upadhvava S K, Shafii S, Garrett R E. Hydropneumatic seeder for primed seed. Tua-nsactions of the ASABE, 1998; 41(2): 307–314.

Jia H L, Chen Y L, Zhao J L, Guo M Z, Huang D Y, Zhang J. Design and key parameter optimization of an agitated soybean seed metering device with horizontal seed filling. Int J Agric & Biol Eng, 2018; 11(2): 76–87.

Singh R C, Singh G, Saraswat D C. Optimization of design and operational parameters of a pneumatic seed metering device for planting cottonseeds. Biosystems Engineering, 2005; 92(4): 429–438.

Yang S H, Sun Y J, Ma C L, Zhao H L. Optimization of parameters of air-blowing vertical-rotor type precision seed-metering device. Transactions of the CSAE, 2008; 24(2): 116–120. (in Chinese)

Ma C L, Li S W. Study on improving the filling speed limit of gas blower. Journal of Jilin University of Technology, 1981; 3: 28–37. (in Chinese)

Hu S R, Ma C L, Li H Z, Li S W. Study on the influence of discharge frequency and air velocity of air-blowing seed meter on seed quality. Journal of Jilin University of Technology, 1981; 4: 26–35. (in Chinese)

Hu S R, Ma C L, Li H Z, Li S W. Study on influence of structural parameters of cone hole of air blowing type meter on seed quality. Transactions of the CSAM, 1981; 3: 21–31. (in Chinese)

Sun Y J, Ma C L, Zhang Z Y. Parameters optimization of precision seed-metering device based on uniform design. Journal of Jilin University (Engineering and Technology Edition), 2004; 4: 569–572. (in Chinese)

Chen Z R, Yu J Q, Xue D M, Wang Y, Zhang Q, Ren L Q. An approach to and validation of maize-seed-assembly modelling based on the discrete element method. Powder Technololgy, 2018; 328(4): 167–183.

Thang C Z, Xiang W B, Xie F P. Experimental study on the air-blown hybrid rice precision seeding device hole type. Transactions of the CSAE, 1999; 15(1): 241–243.

Liu J, Cui T, Zhang D X, Huang S L, Shi S. Experimental study on pressure of air-blowing precision seed-metering device. Transactions of the CSAE, 2011; 27(12): 18–22. (in Chinese)

Y u J J, Liao Y T, Cong J L, Y ang S, Liao Q X. Simulation analysis and match experiment on negative and positive pressures of pneumatic precision metering device for rapeseed. Int J Agric & Biol Eng, 2014; 7(3): 1–12.

Li M, Liu X H, Liao Y T, Liao Q X. Pneumatic cylinder-type centralized precision metering device for rapeseed. Transactions of the CSAM, 2013; 44(12): 68–73. (in Chinese)

Li M, Liao Q X, Liao Y T, Shu C X, Li L. Analysis on seeding process of pneumatic cylinder-type centralized rapeseed precision metering device. Transactions of the CSAE, 2014; 30(23): 17–27. (in Chinese)

Lai Q H, Cao X L, Yu Q X, Sun K, Qin W. Design and experiment of precision seeding device for hole-dropplanter for panax notoginseng. Transactions of the CSAM, 2019; 50(1): 85–95. (in Chinese)

Yin X W, Yang L, Zhang D X, Cui T, Han D D, Zhang T L. Design and experiment of balanceand low-loss air allotter in air pressure maize precision planter. Transactions of the CSAE, 2016; 32(19): 9–17. (in Chinese)

Zhang Z S. Fluid mechanics (The Third Edition). Tsinghua University Press, 2015; pp.108–120.

Zhang B P. Design principle of seeding machinery. China Machine Press, 1982. (in Chinese)

Chen Z, Handbook of agricultural machinery design. China Agricultural Science and Technology Publishing House, 2007. (in Chinese)

Ren C, Gao X J, Su W, Wang Z Y, Lai Q H. Experimental study on physical and mechanical characteristicsof Panax notoginseng seeds. Journal of Hunan Agricultural University (Natural Sciences), 2015; 41(1): 109–112. (in Chinese)

Xing H, Wang Z M, Luo X W, Zang Y, Yang W W, Zhang M H. Design of an active seed throwing and cleaning unit for pneumatic rice seed metering device. Int J Agric & Biol Eng, 2018; 11(2): 62–69.

Li J H. Multi-scale simulation of particle-fliud complex systems. Science Publishing Company, 2005. (in Chinese)

Han D D, Zhang D X, Jing H R, Yang L, Cui T, Ding Y Q. DEM-CFD coupling simulation and optimization of an inside-filling air-blowing maize precision seed-metering device. Computers and Electronics in Agriculture, 2018; 150(6): 426–438.

GB/T 6973-2005 single (precise) test method. National Standards of the People’s Republic of China. (in Chinese).

Zhao X M. Test design method. Science Publishing Company, 2006. (in Chinese)




Copyright (c) 2020 International Journal of Agricultural and Biological Engineering

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

2023-2026 Copyright IJABE Editing and Publishing Office