Microwave drying kinetics and quality characteristics of corn
DOI:
https://doi.org/10.25165/ijabe.v6i1.751Keywords:
microwave drying, corn, stress-crack, germination, bulk density, true densityAbstract
In recent years, microwave (MW) drying has gained popularity as an alternative drying method for a wide variety of food and agricultural products because of increasing concerns over product quality and production costs. However, the determination of drying kinetics that accurately describes microwave drying characteristics is crucial for the optimization of operating parameters, performance improvement of the drying system and product quality. The objective of this study was to investigate the drying kinetics and the quality characteristics of corn kernels, especially the effects of different initial moisture contents (18.3%, 26.3%, 34.3% and 42.3% db), MW power levels (70, 175 and 245 W) and exposure time (80 s and 120 s) on the drying kinetics, drying rate and various key quality parameters. The results indicated that the increased drying rate at higher power levels (P3, 245 W) reduced the drying time considerably but increased stress crack index and reduced germination. In addition, it reduced bulk density, true density and thousand grain weight (TGW). The germination rate of corn was the highest at MW power level P1 (70 W), with the lowest drying rate and observed to decrease with increase in initial moisture content. The reduction in exposure time decreased stress crack index and increased germination rate, bulk density and true density. The correlation analysis among drying rate, germination, stress-crack index (SCI), bulk density, true density and TGW showed that increasing drying rate could lead to an increase in SCI and decrease in germination, bulk density and true density.References
FAO. FAOSTAT. Food and Agriculture Organization of the United Nations, 2010; Roma, Italy.
USDA. United States Standards for Corn. 1996; Available online: http://www.gipsa.usda.gov/fgis/standards/ 810corn.pdf.
Wall J S, James C, Donaldson G L. Corn proteins: Chemical and physical changes during drying of corn. Cereal Chemistry, 1975; 52 (6): 779-790.
Herter U, Burris J S. Preconditioning reduces the susceptibility to drying incury in corn seed. Canadian Journal of Plant Science, 1989; 69: 775-789.
Elikhani Z. Zeolites as particulate medium for contact heating and drying of corn. The thesis submitted to the Faculty of Graduate Studies and Research of McGill University, Québec, Canada. 1990.
Bengtsson N E, Ohlsson T. Microwave heating in the food industry. Proceedings of the IEEE, 1974; 62(1): 44–55.
Zhou L, Puri V M, Anantheswaran R C. Effect of temperature gradient on moisture migration during microwave heating. Drying Technology, 1994; 12(4): 777-798.
Odjo S, Malumba P, Dossou J, Janas S, Béra F. Influence of drying and hydrothermal treatment of corn on the denaturation of salt-soluble proteins and color parameters. Journal of Food Engineering, 2012; 109(3): 561-570.
Sale A J H. A review of microwave for food processing. International Journal of Food Science & Technology, 1976; 11(4): 319-329.
Shivhare U S. Drying characteristics of com in a microwave field with a surface-wave applicator. PhD. thesis, Macdonald Campus of McGill University, 1991.
Gunasekaran S. Pulsed microwave and vacuum drying of food materials. Drying Technology, 1999; 17(3): 395-412.
Reyes A, Cerón S, Zủňiga R, Moyano P. A comparative study of microwave-assisted air drying of potato slices. Biosystem Engineering, 2007; 98: 310-318.
Good D L, Hill L D. Illinois and the world corn market. Illinois Research, 1992; 34(1-2): 3-7.
Weller C L, Paulsen M R, Steinberg M P. Correlation of starch recovery with assorted quality factors of four corn hybrids. Cereal Chemistry, 1988; 65(5): 392-397.
Peplinski A J, Paulis J W, Bietz J A, Pratt R C. Drying of high-moisture corn: Changes in properties and physical quality. Cereal Chemistry, 1994; 71(2): 129-133.
Paulsen M R, Hofing S L, Hill L D, Eckhoff S R. Corn quality characteristics for Japan markets. Applied Engineering in Agriculture, 1996; 12(6): 731-738.
Paulsen M R, Hill L D. Corn quality factors affecting dry milling performance. Journal of Agricultural Engineering
Research, 1985; 31: 255-263.
Montross M D, Bakker-Arkema F W, Hines R E. Moisture content variation and grain quality of corn dried in different high-temperature dryers. Transactions of the ASAE, 1999; 42(2): 427-433.
Watkins A E, Maier D E. Thin layer drying rates and stress cracking of white food corn hybrids. ASAE Paper No. 97-6065, 1997.
Weller C L, Paulsen M R, Steinberg M P. Stress crackıng and breakage susceptibility as affected by moisture content at harvest for four yellow dent corn hybrıds. Transactions of the ASAE, 1990; 33(3): 863-869.
Nair G R, Li Z, Gariepy Y, Vijaya R. Microwave drying of corn (Zea mays L. ssp.) for the seed industry. Drying Technology, 2011; 29(11): 1291-1296.
Gunasekaran S. Drying corn using continuous and pulsed microwave energy. Drying Technology, 1990; 8(5): 1039- 1047.
Shivhare U S, Raghavan G S V, Bosisio R G. Microwave drying of corn II. Constant power, continuous operation. Transaction of the ASAE, 1992; 35(3): 951-958.
Chung M T M, Furutani S C. Microwave Drying of Macadamia Nuts. Applied Engineering in Agriculture, 1989; 5(4): 565-567.
Vicaş S, Ioan M. The drying process of corn seeds in the microwave field. Analele Universităţii din Oradea, Fascicula Protecţia Mediului, XVI, 2011; 191-197.
Vicaş S M, Palade P A. The drying processes of corn seeds
in microwave field. Analele Universită Ńii din Oradea Fascicula: Ecotoxicologie, Zootehnie si Tehnologii de Industrie Alimentară, 2010; 1278-1286.
Manickavasagan A, Jayas D S, White N D G. Germination of wheat grains from uneven microwave heating in an industrial microwave dryer. Canadian Biosystem Engineering, 2007; 49(3): 23-27.
Campaña L A, Sempé M E, Filgueira R R. Physical, chemical and baking properties of wheat dried with microwave energy. Cereal Chemistry, 1993; 70: 760-763.
Nofsinger G W, Van Cauwenberge J E, Anderson R A, Boathast R J. Preliminary biological evaluation of the effect of microwave heating on high-moisture shelled corn. Cereal Chemistry, 1980; 57(6): 373-375.
Velu V, Nagender A, Prabhakara Rao P G. Rao D G. Dry milling characteristics of microwave dried maize grains (Zea mays L.). Journal of Food Engineering, 2006; 74: 30-36.
Kirleis A W, Stroshine R L. Effects of hardness and drying air temperature on breakage susceptibility and dry-milling characteristics of yellow dent corn. Cereal Chemistry, 1990; 67(6): 523-528.
Mohsenin N N. Physical Properties of Plant and Animal Materials. Gordon and Breach Science Publishers, New York, 1980.
Seifi M R, Alimardani R. Comparison of moisture-dependent physical and mechanical properties of two varieties of corn (Sc 704 and Dc 370). Australian Journal of Agricultural Engineering, 2010; 1(5): 170-178.
Downloads
Published
How to Cite
Issue
Section
License
IJABE is an international peer reviewed open access journal, adopting Creative Commons Copyright Notices as follows.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
