Numerical methods and failure mechanisms of ferrofluid seals in centrifugal pumps

Authors

  • Wangxu Li 1. School of Energy and Power Engineering, Lanzhou University of Technology, Lanzhou 730050, China
  • Hongliang Li 1. School of Energy and Power Engineering, Lanzhou University of Technology, Lanzhou 730050, China
  • Zhenggui Li 1. School of Energy and Power Engineering, Lanzhou University of Technology, Lanzhou 730050, China; 2. School of Engineering, Qinghai Institute of Technology, Xining 810016, China
  • Wei Han 1. School of Energy and Power Engineering, Lanzhou University of Technology, Lanzhou 730050, China; 3. School of Green Energy and Energy Storage, Lanzhou University of Technology, Lanzhou 730050, China
  • Rennian Li 1. School of Energy and Power Engineering, Lanzhou University of Technology, Lanzhou 730050, China
  • Yue Zhang 1. School of Energy and Power Engineering, Lanzhou University of Technology, Lanzhou 730050, China

Abstract

Ferrofluid seals are considered a next-generation sealing technology for hydraulic machinery due to their outstanding performance. However, experiments and engineering applications have revealed issues with seal failure, the mechanisms of which remain poorly understood. This study focuses on centrifugal pumps, employing numerical simulations to analyze the hydrodynamic characteristics and pressure pulsations in the sealing clearance. A coupling interface between the three-dimensional fluid machinery numerical results and two-dimensional ferrofluid seal numerical results was established to investigate the effects of mean and pulsating pressures on the ferrofluid interface morphology and the mechanisms of seal failure. The results indicate that the rotation of the centrifugal pump shaft induces forced vortices in the sealing clearance. Influenced by the clearance structure, these forced vortices generate free vortices with similar flow patterns. The vortex motion is identified as the primary factor causing pressure pulsations in the sealing clearance, with an amplitude of approximately 0.18 MPa due to scale limitations. Compared to the morphology of ferrofluid seals under mean pressure, pulsating flow does not cause partial detachment of the ferrofluid but accelerates the rupture process of the ferrofluid sealing ring. Under the critical pressure of the ferrofluid sealing ring, pulsating pressure causes significant damage within 0.8 s. This study concludes that the stability and failure of ferrofluid seals in centrifugal pumps are strongly governed by vortex-induced pressure fluctuations and the interaction between magnetic field distribution and flow dynamics. The designed four-level ferrofluid sealing device can effectively withstand peak pressure pulsations, demonstrating reliable sealing performance. These findings provide critical insights for optimizing ferrofluid seal designs and can guide the development of more reliable sealing technologies in high-speed hydraulic machinery, improving operational safety and efficiency.      

Keywords: hydraulic machinery, ferrofluid seal, multi-field coupling, failure mechanism

DOI: 10.25165/j.ijabe.20261902.10146

 

Citation: Li W X, Li H L, Li Z G, Han W, Li R N, Zhang Y. Numerical methods and failure mechanisms of ferrofluid seals in centrifugal pumps. Int J Agric & Biol Eng, 2026; 19(2): 183–192.

References

[1] Yang X W. Causes and fault handling of mechanical seal leakage in centrifugal pumps. Chemical Engineering and Equipment, 2023; 3: 172–174.

[2] Zhai L. Numerical simulation and experimental study on the dynamic characteristics of hermetic groove circulation labyrinth seals in centrifugal pumps. Zhejiang University, 2015.

[3] Wu M. Analysis and countermeasures of soft packing seal problems in centrifugal pumps. Manufactured and Upgraded Today, 2023; 6: 77–79, 129.

[4] Li W X, Li Z G, Han W, Li D C, Yan S N, Zhou J P. Study of the flow characteristics of pumped media in the confined morphology of a ferrofluid pump with annular microscale constraints. Journal of Fluids Engineering, 2025; 147（2）: 021201.

[5] Li W X, Li Z G, Han W, Li R N, Zhang Y. Mechanism of bubble generation in ferrofluid micro-pumps and key parameters influencing performance. Powder Technology, 2026; 467（15）: 121562.

[6] Li W X, Li Z G, Han W, Wang Y, Zhao J L, Zhou J P. Morphologic transformation of ferrofluid during micropump driving under field control. Annals of the New York Academy of Sciences, 2025; 1543（1）: 194–203.

[7] Chen F, Zhang J, Guo Q K, Liu Y C, Liu X B, Ding W W, et al. Carbonyl iron particles’ enhanced coating effect improves magnetorheological fluid’s dispersion stability. Materials, 2024; 17（18）: 4449.

[8] Li W X, Li Z G, Han W, Li Y B, Yan S N, Zhao Q, et al. Measured viscosity characteristics of Fe3O4 ferrofluid in magnetic and thermal fields. Physics of Fluids, 2023; 35（1）: 012002.

[9] Li W X, Yin J Y, Li Z G, Han W. Experimentally validated model of ferrofluid flow in micropumps. International Journal of Mechanical Sciences, 2026; 314: 111386.

[10] Nguyen D T, Nguyen N T, Nguyen M Q, Pham T T T, Le A D. Application of magnetic liquid slurries and fuzzy grey analysis in polishing nickel-phosphorus coated SKD11 steel. Particulate Science and Technology, 2022; 40（4）: 401–414.

[11] Li D C, Xu H P, He X Z, Lan H Q. Study on the magnetic fluid sealing for dry Roots pump. Journal of Magnetism and Magnetic Materials, 2005; 289: 419–422.

[12] Fan D. Research on the magnetic viscosity effect of magnetic liquids at different temperatures. Beijing: Beijing Jiaotong University, 2012; 57p.

[13] Li W X, Li Z G, Zhao Q, Yan S N, Wang Z Y, Peng S Y. Influence of the solution pH on the design of a hydro-mechanical magneto-hydraulic sealing device. Engineering Failure Analysis, 2022; 135: 106091.

[14] Li Z G, Li W X, Wang Q F, Xiang R, Cheng J, Han W, et al. Effects of medium fluid cavitation on fluctuation characteristics of magnetic fluid seal interface in agricultural centrifugal pump. Int J Agric & Biol Eng, 2021; 14（6）: 85–92.

[15] Liu T G, Cheng Y S, Yang Z Y. Design optimization of seal structure for sealing liquid by magnetic fluids. Journal of Magnetism and Magnetic Materials, 2005; 289: 411–414.

[16] Yoshinori M, Durst C A. Miniature magnetic fluid seal working in liquid environments. Journal of Magnetism and Magnetic Materials, 2017; 431: 285–288.

[17] Matuszewski L, Szydło Z. Life tests of a rotary single-stage magnetic-fluid seal for shipbuilding applications. Polish Maritime Research, 2011; 51–59.

[18] Szydło Z, Szczech M. Investigation of dynamic magnetic fluid seal wear process in utility water environment. Key Engineering Materials, 2012; 490: 143–155.

[19] Matuszewski L. Multi-stage magnetic-fluid seals for operating in water–life test procedure, test stand and research results, Part I: Life test procedure, test stand and instrumentation. Polish Maritime Research, 2012; 14（9）: 62–70.

[20] Marcin S, Horak W. Tightness testing of rotary ferromagnetic fluid seal working in water environment. Industrial Lubrication and Tribology, 2015; 67（5）: 455–459.

[21] Li X R, Fan X Q, Li Z G, Zhu M H. Failure mechanism of magnetic fluid seal for sealing liquids. Tribology International, 2023; 187: 108700.

[22] Qian J, Yang Z. Analysis of liquid-liquid interface stability of magnetic-hydraulic dynamic seals. Fluid Machinery, 2008; 36（12）: 21–23, 20.

[23] Chen Y B, Li D C, Li Z K, Zhang Y J. Numerical analysis on boundary and flow regime of magnetic fluid in the sealing clearance with a rotation shaft. IEEE Transactions on Magnetics, 2018; 55（2）: 1–7.

[24] Le M, Yu S, Su H, Ning Q, Zhou W. Static and rotordynamic characteristics of a sectorial labyrinth seal for centrifugal pump. Tribology International, 2025; 214: 111375.

[25] Zhou W J, Su H H, Liu H, Zhang Y, Qiu N, Gao B. Leakage and rotordynamic performance of a semi-Y labyrinth seal structure for centrifugal pump based on multi-frequency whirl method. Journal of Engineering for Gas Turbines and Power, 2025; 147（10）: 101022.

[26] Xu L C, Zhang Y Q, Xu J H, Wang Y R, Chen F, Yang Y X, et al. Towards the integration of new-type power systems: Hydraulic stability analysis of pumped storage units in the S-characteristic region based on experimental and CFD studies. Energy, 2025; 329: 136755.

[27] Xu L C, Zhang Y Q, Xu J H, Zhang D S, Feng C, Zhang Z, et al. Vortex and energy characteristics in the hump region of pump-turbines based on the rigid vorticity and local hydraulic loss method. Physics of Fluids, 2025; 37（3）: 035194.

[28] Ren Z P, Li D Y, Meng Z F, Liu N N, Khoo B C. Spatial-temporal correlation and fluctuating propagation characteristics of bubbles based on a coupled model of oscillation and migration. Applied Ocean Research, 2025; 161: 104677.

[29] Liang A, Chang Y Z, Zhang W W, Yao Z F, Zhu B S, Wang F J. Research on the evolution law and energy loss characteristics of rotating stall in a pump-turbine under pump mode. Energy, 2025; 330: 136696.

[30] Liang A, Zhang W W, Zhao H R, Zhou P J, Yao Z F, Zhu B S. Research on the energy loss characteristics in the double-hump region of a pump-turbine. Physics of Fluids, 2025; 37（9）: 095144.

[31] Ren Z P, Li D Y, Li Z P, Wang H J, Liu J T, Li Y, et al. Absorbed-desorbed effects of ventilated pipeline. International Communications in Heat and Mass Transfer, 2025; 167（B）: 109308.

[32] Li W X, Han W, Li Z G, Li R N, Zhang Y. Research on the flow rate characteristics and velocity pulsation behavior of ferrofluid micro pumps. Chemical Engineering Journal, 2025; 526: 171211.

[33] Cheng J, Li Z G, Li W X, Li X R, Gong J C. The influence of key parameters of pole teeth on the sealing pressure of the magnetohydrodynamic sealing device. Magnetic Materials and Devices, 2021; 52（5）: 34–41.

[34] Li Z G, Wang M G, Chen F, Yan S N, Li W X, Cheng J. Influence of the axial tooth structure on the pressure resistance of the magnetic fluid sealing device. Vacuum, 2022; 202: 111105.

Downloads

Published

2026-05-21

How to Cite

(1)
Li, W.; Li, H.; Li, Z.; Han, W.; Li, R.; Zhang, Y. Numerical Methods and Failure Mechanisms of Ferrofluid Seals in Centrifugal Pumps. Int J Agric & Biol Eng 2026, 19, 183-192.

Issue

Vol. 19 No. 2 (2026): IJABE

Section

Power and Machinery Systems

License

Copyright (c) 2026 International Journal of Agricultural and Biological Engineering

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

IJABE is an international peer reviewed, open access journal, adopting Creative Commons Copyright Notices as follows.

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).

Most read articles by the same author(s)