Calibration of rototilled soil block discrete element parameters after rotary tillage in rape planting by machinery
Abstract
This study sought to construct and empirically validate a discrete element method (DEM) particle model representing post-tillage soil blocks. This model was developed to facilitate a detailed examination of granular movement and contact mechanics during the shaping process of planting chambers for rape plants. The research specifically targeted the sticky, cohesive soil prevalent in rice paddy fields of the middle and lower Yangtze River region. Simulations were conducted using EDEM software to improve the accuracy with which soil-tool interactions are predicted for the design and optimization of mechanical transplanters. The physical and bonding parameters of the sticky soil were calibrated using the Hertz-Mindlin with Johnson-Kendall-Roberts (JKR) contact model and Hertz-Mindlin with Bonding contact model. A particle replacement method was adopted to create a discrete element model of cohesive soil aggregates with different shapes and sizes after rotary tillage. The accumulation angle of soil aggregates was used as the evaluation index in both the simulation and physical experiments. Design-Expert software was used to design a four-factor, three-level simulation experiment to identify the optimal parameter combinations for the physical and mechanical properties of the sticky soil and the JKR contact model, which comprised a soil-soil static friction coefficient of 0.32, soil-soil rolling friction coefficient of 0.10, soil-steel static friction coefficient of 0.51, and surface energy of soil for the JKR model of 5.50 J/m2. Next, the steepest climbing test and Box-Behnken orthogonal combination test were then used to narrow down the range of values for the significant factors and identify the optimal parameter combinations for the bonding contact model parameters, which included a bonding bond normal contact stiffness of 2.1×106 N/m, a bonding bond tangential contact stiffness of 2.2×106 N/m, a normal ultimate stress of 0.55 MPa, a tangential ultimate stress of 0.55 MPa, and a bonding radius of 12 mm. Field experiments were conducted using a flat box device to measure the soil evenness and firmness after ridge formation and compaction by a rotary tiller. The results of these experiments were compared with the discrete element simulation optimization results. The relative errors between the field test results and the simulation test results for soil flatness and compaction were 10.7% and 9.8%, respectively, which indicated good accuracy of the parameters calibrated and optimized by EDEM discrete element simulation software. Overall, this research can provide a reference for understanding the working mechanism and optimizing the parameters of soil touching components in rape transplanting equipment.
Keywords: rape, soil block, soil firmness, discrete element method, parameter calibration
DOI: 10.25165/j.ijabe.20261902.9590
Citation: Shi F G, Wu M L, Zhao Z H, Chen H Y, Jiang X H, Quan W. Calibration of rototilled soil block discrete element parameters after rotary tillage in rape planting by machinery. Int J Agric & Biol Eng, 2026; 19(2): 28–38.
References
[1] Shi Y Y, Wang X C, Hu Z C, Gu F W, Wu F, Chen Y Q. Optimization and experiment on key structural parameters of no-tillage planter with straw-smashing and strip-mulching. Int J Agric & Biol Eng, 2021; 14（3）: 103–111.
[2] Zeng Z W, Ma X, Cao X L, Li Z H, Wang X C. Critical review of applications of discrete element method in agricultural engineering. Transactions of the CSAM, 2021; 52（4）: 1–20.
[3] Hao Z H, Zheng E L, Li X, Yao H P, Wang X C, Qian S Y, et al. Performance analysis of the soil-contacting parts for no-tillage planters and optimization of blade structure. Transactions of the CSAE, 2023; 39（2）: 1–13. （in Chinese）
[4] Zhou J C, Zhang L B, Hu C, Li Z H, Tang J J, Mao K M. Calibration of wet sand and gravel particles based on JKR contact model. Powder Technology, 2022; 397: 117005.
[5] Ma S, Xu L M, Yuan Q C, Niu C, Zeng J, Chen C, et al. Calibration of discrete element simulation parameters of grapevine antifreezing soil and its interaction with soil-cleaning components. Transactions of the CSAM, 2020; 36（1）: 40–49. （in Chinese）
[6] Koushkaki H R, Eshkaftaki M M, Nejadian H A. Simulation of draught force during chisel ploughing using discrete element method. Journal of Biosystems Engineering, 2022; 47: 152–166.
[7] Ucgul M, Saunders C, Fielke J M. Discrete element modelling of top soil burial using a full scale mouldboard plough under field conditions. Biosystems Engineering, 2017; 160: 140–153.
[8] Ding Q S, Ren J, Belal E A, Zhao J K, Ge S Y, Li Y. DEM analysis of subsoiling process in wet clayey paddy soil. Transactions of the CSAM, 2017; 48（3）: 38–48. （in Chinese）
[9] Xiang W, Wu M L, Lv J N, Quan W, Ma L, Liu J J. Calibration of simulation physical parameters of clay loam based on soil accumulation test. Transactions of the CSAE, 2019; 35（12）: 116–123. （in Chinese）
[10] Wang X L, Zhong X K, Geng Y L, Wei Z C, Hu H, Geng D Y, et al. Construction and parameter calibration of the nonlinear elastoplastic discrete element model for no-tillage soil compaction. Transactions of the CSAE, 2021; 37（23）: 100–107. （in Chinese）
[11] Dai F, Song X F, Zhao W Y, Zhang F W, Ma H J, Ma M Y. Simulative calibration on contact parameters of discrete elements for covering soil on whole plastic film mulching on double ridges. Transactions of the CSAM, 2019; 50（2）: 49–56,77. （in Chinese）
[12] Du J, Heng Y F, Zheng K, Luo C M, Zhu Y H, Zhang J M, et al. Investigation of the burial and mixing performance of a rotary tiller using discrete element method. Soil and Tillage Research, 2022; 220: 105349.
[13] Li M L, Wang L Z, Liao Q X, Liao Y T, Xiao W L, Zhang Q S. Calibration of rototilled soil discrete element parameters after rotary tillage in the preparation process of rapeseed mechanized direct seeding micro-ridge seed bed. Transactions of the CSAE, 2023; 39（20）: 10–19. （in Chinese）
[14] Aikins K A, Ucgul M, Barr J B, Jensen T A, Antille D L, Desbiolles J M. Determination of discrete element model parameters for a cohesive soil and validation through narrow point opener performance analysis. Soil and Tillage Research, 2021; 213: 105123.
[15] Wang X Q, Yu G H, Liu N H, Tong J H, Wang Q Y. Calibration of discrete element simulation parameters for greenhouse inferior seedling substrate. Transactions of the CSAM, 2023; 54（12）: 359–366. （in Chinese）
[16] Song Z H, Li H, Yan Y F, Tian F Y, Li Y D, Li F D. Calibration method of contact characteristic parameters of soil in mulberry field based on unequal-diameter particles DEM theory. Transactions of the CSAM, 2022; 53（6）: 21–33. （in Chinese）
[17] Milkevych V, Munkholm L J, Chen Y, Nyord T. Modelling approach for soil displacement in tillage using discrete element method. Soil and Tillage Research, 2018; 183: 60–71.
[18] Fang H M, Ji C Y, Farman A C, Guo J, Zhang Q Y, Chaudhry A. Analysis of soil dynamic behavior during rotary tillage based on distinct element method. Transactions of the CSAM, 2016; 47（3）: 22–28. （in Chinese）
[19] Zhu H B, Wu X, Bai L Z, Qian C, Zhao H R, Li H. Development of the biaxial stubble breaking no-tillage device for rice stubble field based on EDEM-ADAMS simulation. Transactions of the CSAE, 2022; 38（19）: 10–22. （in Chinese）
[20] Yang M X. Numerical study on particle crushing of coarse-grained soil based on discrete element method. Master dissertation. Dalian: Dalian University of Technology, 2020; 69p. （in Chinese）
[21] Liu W Z, He J, Li H W, Li X Q, Zheng K, Wei Z C. Calibration of Simulation parameters for potato minituber based on EDEM. Transactions of the CSAM, 2018; 49（5）: 125–135, 142. （in Chinese）
[22] Luo S, Yuan Q X, Shaban G, Yang L Y. Parameters calibration of vermicomposting nursery substrate with discrete element method based on JKR contact model. Transactions of the CSAM, 2018; 49（4）: 343–350. （in Chinese）
[23] Zhang Z H, Zhao L L, Lai Q H, Tong J. Operation mechanism analysis and experiments of shovel-type rolling soil-engaging components based on DEM-MBD coupling. Transactions of the CSAE, 2022; 38（15）: 10–20. （in Chinese）
[24] Sun J B, Liu Q, Yang F Z, Liu Z J, Wang Z. Calibration of discrete element simulation parameters of sloping soil on loess plateau and its interaction with rotary tillage components. Transactions of the CSAM, 2022; 53（1）: 63–73. （in Chinese）
[25] Tian X L, Cong X, Qi J T, Guo H, Li M, Fan X H. Parameter Calibration of Discrete Element Model for Corn Straw - Soil Mixture in Black Soil Areas. Transactions of the CSAM, 2021; 52（10）: 100–108, 242. （in Chinese）
[26] Xie W, Peng L, Jiang P, Meng D X, Wang X S. Discrete element model building and optimization of double-layer bonding of rape shoots stems at harvest stage. Transactions of the CSAM, 2023; 54（5）: 112–120. （in Chinese）
[27] Tu M, Cao T, Wan Z H, Mo H T, Zhang G Z. Calibration and shear experiments of discrete element bonding parameters for water caltrop. Journal of Huazhong Agricultural University, 2023; 42（4）: 270–278. （in Chinese）
[28] Jia H L, Deng J Y, Deng Y L, Chen T Y, Wang G, Sun Z J, et al. Contact parameter analysis and calibration in discrete element simulation of rice straw. Int J Agric & Biol Eng, 2021; 14（4）: 72–81.
[29] Chen T, Yi S J, Li Y F, Tao G X, Qu S M, Li R. Establishment of discrete element model and parameter calibration of alfalfa stem in budding stage. Transactions of the CSAM, 2023; 54（5）: 91–100. （in Chinese）
[30] Wei Z C, Su G L, Li X Q, Wang F M, Sun C Z, Meng P X. Parameter Optimization and test of potato harvester wavy sieve based on EDEM. Transactions of the CSAM, 2020; 51（10）: 109–122. （in Chinese）
[31] Wang X Z, Yue B, Gao X J, Zheng Z Q, Zhu R X, Huang Y X. Discrete Element simulations and experiments of disturbance behavior as affected by mounting height of subsoiler’s wing. Transactions of the CSAM, 2018; 49（10）: 124–136.
[32] Hu L, Du P, Luo X W, Zhou H, Tang L M, Su H Y. Design and experiment on multi-wheel support laser land leveler hanging on tractor. Transactions of the CSAM, 2019; 50（8）: 15–21. （in Chinese）
[33] Li Q, Luo X W, Wang M H, Zhao Z X, Xu Y J, Ou Y G, et al. Design of a laser land leveler for paddy field. Transactions of the CSAE, 2007; 23（4）: 88–93. （in Chinese）
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 International Journal of Agricultural and Biological Engineering
This work is licensed under a Creative Commons Attribution 4.0 International License.
IJABE is an international peer reviewed, open access journal, adopting Creative Commons Copyright Notices as follows.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
